2-Teat Lamb Feeding Bucket

The 2-Teat Lamb Feeding Bucket is a compact multi-animal milk feeding solution designed for orphan lambs, goat kids and other young small ruminants. Two independent teat positions allow two animals to nurse simultaneously, reducing the labor required for individual bottle feeding.

The reference configuration uses a 2.5-gallon square, see-through bucket with a flat-back profile, two pre-drilled teat positions, soft flat-back latex teats and easy-clean teat units. The transparent body allows operators to monitor milk level quickly, while the sloped bucket floor helps minimize residual milk after feeding.

The feeder can be mounted against livestock pen panels, wire fencing or compatible wooden partitions using a suitable bucket holder. It is well suited to lambing barns, nursery pens, commercial sheep farms, goat farms and livestock equipment projects where reliable group feeding and convenient maintenance are required.

• Two Feeding Positions: Allows two lambs or goat kids to feed at the same time from separate teats.
• Transparent Bucket Body: Makes it easier to monitor remaining milk or milk replacer without removing the feeder.
• Flat-Back Configuration: Designed to sit securely against a livestock panel, pen wall or compatible mounting surface.
• Sloped Internal Floor: Helps direct milk toward the teat area and reduces unused liquid remaining in the bucket.
• Soft Latex Teats: Flat-back natural latex teats are suitable for young lambs and goat kids beginning artificial feeding.
• Easy-Clean Teat Units: The main fitting can remain attached to the bucket while the teat and flow-control component are removed for washing.
• Removable Lid: Helps protect milk from barn contamination, birds and rodents during use.
• Visible Volume Markings: Printed measurement graduations assist with monitoring milk quantity.
• Stable Pen Mounting: Compatible hanging brackets help secure the bucket on wire panels or suitable wooden partitions.
• Reduced Bottle-Feeding Labor: Suitable for farms managing multiple orphaned or supplementary-fed young animals.

Milk or properly prepared milk replacer is poured into the bucket reservoir. Each teat is installed near the lower section of the bucket through an individual teat unit and flow-control assembly.

When a lamb or goat kid suckles, milk is drawn from the reservoir through the corresponding teat unit. The two separate feeding points allow two animals to nurse independently at the same time.

For correct nursing posture, the bucket should be mounted low enough for the animal to stretch its neck naturally while feeding. Mounting height should be adjusted according to animal size and pen configuration.

• Orphan lamb artificial rearing
• Bottle-lamb transition to group feeding
• Supplementary feeding of multiple-birth lambs
• Goat kid milk-feeding programs
• Commercial sheep breeding farms
• Lambing sheds and maternity pens
• Young-stock nursery areas
• Livestock breeding and research facilities
• Small-ruminant farm construction projects
• Livestock equipment dealer and distributor supply programs

• Bucket capacity according to project requirements
• Number and position of teat openings customizable
• Latex or rubber teat options available upon request
• Alternative teat hardness according to animal age
• Mounting bracket configuration according to pen structure
• Bucket color or transparency options available upon request
• Replacement teat, valve and washer kits
• OEM and private-label packaging
• Bulk supply for livestock equipment projects and distributors

Installation:

1. Select a stable wire panel, livestock gate or suitable wooden partition for mounting.
2. Install the compatible bucket holder and confirm that it can support the filled feeder securely.
3. Place the flat-back bucket into the holder and check that it remains stable during animal contact.
4. Position the teats approximately at natural udder height for the animals being fed.
5. Fill the clean bucket with milk or properly mixed milk replacer.
6. Check both teat units for correct milk flow before allowing animals to nurse.

Maintenance:

• Remove residual milk and wash the bucket regularly according to the farm hygiene program.
• Remove the latex nipples and flow-control components from the easy-clean teat units for thorough washing.
• Inspect teats for bite damage, splitting, hardening or deformation.
• Check teat-unit seals and fittings for leakage or blockage.
• Replace worn teats and damaged flow-control parts promptly.
• Keep rubber and latex components away from prolonged direct sunlight during storage.
• Do not leave an empty feeder accessible to lambs or goat kids for long periods, as chewing can damage the teats.

Q1: How many animals can use the feeder at once?

The standard two-teat configuration provides two independent feeding positions for two lambs or goat kids.

Q2: What is the reference capacity?

The referenced square bucket configuration has a capacity of 2.5 US gallons.

Q3: Why is the bucket transparent?

The see-through body allows farm staff to check milk level quickly and monitor feeding without opening the bucket repeatedly.

Q4: Why is the bottom of the bucket sloped?

The sloped floor helps move milk toward the teat area so that less liquid remains unused at the bottom of the feeder.

Q5: Are latex teats suitable for newborn lambs?

Yes. Soft flat-back latex teats are particularly suitable for young lambs and goat kids beginning artificial feeding, although rubber teats can offer greater durability as animals become older and develop sharper teeth.

Q6: Can the teat units be cleaned without removing the complete fitting?

Yes. With the easy-clean configuration, the main teat unit remains attached to the bucket while the nipple and flow-control component can be removed for washing.

Q7: Can the bucket be mounted on livestock fencing?

Yes. A compatible wire holder can secure the bucket to livestock panels or suitable wooden partitions.

Q8: Can SHEWUYOU customize the feeder?

Yes. Bucket configuration, teat type, mounting arrangement, packaging and related replacement components can be supplied according to project requirements.